Wednesday, October 13, 2021

Signs of a broken CVT Motor Matic

Knowing the damage to the CVT of an automatic motorcycle is one of the maintenance steps to maintain the performance of an automatic motorcycle engine

 



Characteristics of a Damaged CVT Matic Motor - It is undeniable that the automatic motor is currently a personal vehicle that is widely chosen by our society.


Practical and flexible to be ridden in all terrains, making scooters also widely owned as the main means of transportation.


Not without reason, by relying on the Continuous Variable Timing transmission, the driver certainly doesn't have to bother pulling the clutch lever or injecting the gear lever. Just step on the gas, the motor can run immediately.


However, you still can not leave the treatment step. Given, does not rule out the potential for damage will still be experienced by this automatic motor.


One component that is also often problematic is the CVT. If this component is damaged, of course the automatic motor will not be able to run.


Therefore, one of the steps to minimize damage is to take steps to prevent damage to the automatic scooter CVT.


Among them is recognizing the early signs or symptoms of CVT motor matic damage. So, it can be repaired immediately without the need to wait until it is completely damaged.


Given, if left alone then the damage to the CVT motor matic will spread to other components.


Therefore, you should recognize the signs or characteristics of a damaged CVT motor matic as a preventive measure to minimize the occurrence of more severe damage.


As a vital component, of course CVT on the scooter must receive serious attention and care. One of them is by recognizing the signs of CVT damage on this automatic motor.


Cvt Motor Matic Broken


Noise is heard in Section V-Belt Section


In general, symptoms of damage to the CVT system on automatic motors can usually be indicated by the presence of noise that appears in the V-Belt sector.


This is a sign that there is a problem with the CVT that requires you to do a thorough check.


Especially if the sound issued is very loud and noisy. So you don't have to wait too long to fix it.


There is a vibration when the motor is gassed


Then, another characteristic that indicates there is a problem with the CVT, of course, can be seen from the vibrations that appear. Especially when the motor is gassed for the first time or during acceleration.


Generally this condition is a sign of damage to the CVT roller. It could be due to age of use or it has started to wear out.


This condition is sometimes not detected at all. However, if there is a vibration, it is a sign that the CVT roller has begun to run out of service and must be replaced immediately.


To be sure, you can ask the mechanic when doing routine service or changing the oil regularly.


The Motor Feels Ndut-Ndut When Gasping


On the other hand, you also have to pay attention to how the condition of the motor when gassed. Because, CVT damage can be known when you run the motor.


Which, there is a feeling of the motor like tripping or stuttering like running out of gas. This is a symptom of a malfunction in the CVT clutch bowl.


If this has happened then you need to do an in-depth examination.


Given, not necessarily the condition of a wobbly motor like this is a sign or characteristic of a damaged CVT. There may be a problem with the chain.


However, if it has happened repeatedly, it is very possible that the CVT automatic motor clutch bowl has problems or damage that needs special repairs.

Motorcycle Spare Parts That Must Be Replaced

Know the automatic motor components that must be replaced regularly.




Motorcycle Spare Parts That Must Be Replaced Regularly – Automatic motorbikes are now a popular vehicle for many people.


The practicality and efficiency of using automatic motorcycles are the main factors that make people in the country prefer motorized vehicles with this automatic transmission.


Even though it's easy to use, you can't use it right away. That is, there must be steps to take care of the automatic motor that you have to do.


In addition to routine service and oil changes, of course you need to know that there are automatic motor components that must be replaced regularly.


Bearing in mind, some of these automatic motorcycle parts have a lifetime which of course must be replaced with new ones. Although, under normal circumstances or can be used.


Replacement components on this automatic motor usually have to be replaced when it reaches a certain period of time. Where, 5 years of service life is the ideal time to replace some critical parts.


Now for more clarity and detail, below Mas Sena will share information related to automatic motorcycle spare parts that must be replaced when the service life reaches 5 years. Let's see the full review together.


Matic Motor Components That Must Be Replaced Periodically

In practice, replacing components on an automatic motor is one of the maintenance steps that you must do. Then, what spare parts need to be replaced? Here's the explanation.


Motor Matic Spare Part Component Maintenance


Motorcycle Tires


The first component you should pay attention to for replacement is the motorcycle tire itself.


Actually the tire is a component whose replacement is quite long compared to other components.


However, as an important component related to driving comfort, of course, it is recommended to change tires regularly.


Try not to change the tire yourself until the surface is flat or bare so as not to slip when passing through slippery road terrain.


Although fairly trivial, it's a good idea to replace these components regularly and regularly. Preferably, the replacement can be done once a year or if it is felt that the tire surface has started to go bald.


And, don't forget to use quality tires. It is recommended to use tubeless tires which of course will be much safer and more effective.


Spark Plug Replacement


In addition, the spare part on the scooter that you must replace regularly is the spark plug. Which is indeed one of the vital components in the combustion process.


You need to understand that the normal condition of the motor's spark plugs will certainly greatly affect or have an impact on the engine performance process. This of course cannot be separated from the role of the spark plug itself as the main component in the ignition process of the automatic motor.


In this case, the main task of these spark plugs is to start a fire or burn. Combustion is done by mixing air and fuel.


For self-replacement, manufacturers generally recommend a replacement period after the motor has traveled 20,000 Km.


It's just that the achievement of this distance is for normal spark plug conditions. Moreover, for some cases, for example, the spark plug is damaged even though it has not reached that distance, you have to replace the new spark plug.


Therefore, you should regularly check the condition of the spark plugs. If you feel the automatic motor feels tight when running, you should check the state of the spark plug. Given, the possibility of an underpowered motor engine condition can be triggered due to a problem with the spark plug component itself.


Matic Motorcycle Brake Pads


Brake pads on automatic motorcycles are also one of the few spare parts that you must replace regularly and periodically.


Because, the function of the brake lining is of course an attempt to control or reduce the speed of the motor while driving. Thus, safety or accidents can be avoided.

Thursday, September 30, 2021

Techniques and How to Feed Wild Birds

Have you ever seen a bird that likes to fly around our house? They go back and forth, sometimes in groups, sometimes alone.




And generally the most common are flocks of sparrows and sparrows in urban areas as well as swallows and sriguntings. In areas close to forest areas, of course, more bird species will be found.


Birds fly out of their nests in search of food. And it's true the saying that says never give up on the fortune that will be picked up, seeing birds leave the nest with an empty stomach and return to the nest with a full stomach can even feed the chicks.


Here's the Technique and How to Feed Wild Birds


It turns out that there is a simple way without the need to spend big if we want to help preserve this bird population.


We can help by providing free feed for them, by providing a variety of seeds and fruit in certain containers that are easily accessible to birds.


One of the advantages that you can feel is that your home environment becomes more lively with the chirping of wild birds that come to eat the free food that has been prepared. Interested in trying it?


Here are some models of free wild bird feeding containers or a cool term for giving alms to other creatures, namely wild birds.


And not only can we provide free feed for wild birds, we can also provide free drinking by placing clean water in special drinking places such as drinking containers in broiler farms and placing it together with free bird feed.


The last tip for conserving wild birds is not to destroy their habitat. Plant trees around our yard because trees will be home to various types of wild birds and will enliven your home with a variety of styles and models of chirping that vary greatly.

How to take care of baby finches

How to care for and care for finches puppies, the experience of finches lovers who have experience caring for this cucak family bird.




How to care for and care for finches


 Stepping:


Combine the chicken puree with water and stir until it becomes a mush (not too runny/liquid).


Feed the puppy using a water straw until it is full. Here I recommend using aqua straws, because if you use a stick, the tip of the stick can hurt the puppy's mouth if the puppy is very hungry and enthusiastic. Therefore, it is recommended to use a water straw for feeding and watering.



How to care for and care for finches


 Notes:


If you want to mix it with bananas, mash the bananas until smooth, then mix with a puree like step no. 1.


Likewise if you want to mix it with Kroto, crickets, or caterpillars. Mix with pur porridge like step no 1.


But it can also be without the need to be mixed with pur porridge. If you want to give crickets and caterpillars, just give crickets and caterpillars that are still small.


Give the pur mixture every 1 or 1.5 hours (if the puppy cannot feed itself at all). But if the saplings can feed themselves, feed them however you like.


There's nothing wrong with bribing every now and then to build a bond between the puppy and you as the master.


Always check by smelling pur mixture, because pur mixture mixed with water will become stale.


The smell of stale pur concoction will be very sour and sour when smelled. Therefore, in making pur mixture, pay attention to the amount of pur, not too much because it is useless, later it must be discarded and replaced with new material if it is stale. Usually the pur concoction will go stale within 5 or 6 hours.


You can invite him to play outside the cage without having to worry about your hero coming out. Even if your hero plays and flies some distance away, give a whistle to call, your hero will definitely come close.

Sunday, September 19, 2021

How to Make a Simple Duck Cage From Bamboo

Duck cages - ducks are indeed farm animals that live in colonies unlike chickens that look for their own food, therefore in raising ducks it is necessary to have quite a lot of ducks.




Ducks usually prefer to be released in rice fields that have been harvested or even in rivers and other places that wallow and water.


How to Make a Duck Cage


There are many things to consider in making a cage that ducks like. namely there are puddles for me to play in and there is also a place to shelter from direct sunlight, lots of cages and what kinds of materials can be used to make a colony of duck cages.


1 . Bamboo


Many can be used from this one plant. For example, only small bamboo shoots, namely (BAMBUNG) which are small bamboo shoots that can be used as food ingredients for many processed foods that use bamboo shoots.


In making the cage must be in accordance with the land to be used, you can example duck cage below:


depending on the size you need, in making the cage it should be about 1 meter or more and made rather tightly so that it makes it difficult for pests that will eat ducks and duck thieves. and don't forget to also make shelter for the ducks from the heat, if the land is large enough, you should make a pond or duck puddle so that the ducks feel at home in the cage.


2 . Waring


For those who don't know waring, I will explain waring which is a long net, which is usually used to make fish cages or protect farmers' fields from disturbances from other animals such as chickens or ducks as well as children playing in the fields.


Is waring good in making duck cages, of course it is better if waring is specially designed to protect waring, indeed waring is not as strong as bamboo, but waring is quite effective in making livestock cages.


if you have a waring that is not used, it is better to use it to make other livestock cages, especially ducks. example of a duck cage that uses waring:


The picture above is only for your reference in making duck cage ideas, for the poles you can use wood, bamboo and iron if you have one. then hooked or tied using a rope or wire commonly used to make castings in buildings. size according to your land.


3 . Wall


This one is indeed a fairly large capital in its manufacture, starting from making a foundation and then making a wall, indeed in this way it is classified as safe from animal attacks, namely monitor lizards and snakes and usually thieves.


wild animals eat duck eggs or even prey on the ducks themselves. in the manufacture according to your wishes or according to your land. Don't forget to also provide shelter for the ducks from the hot sun or rain and the good thing is that in the duck cage there is also land for ducks or pools of water to swim to get additional feed too.

How to Make a Quality Goat Cage

A good cage system will determine the success of the goat business.




This is because the cage system will assist in goat rearing management such as facilitating feeding and drinking, mating, handling births, handling sick goats, and others.


For example, when the farmer is going to give feed, it will be difficult if the feeder is too high because the farmer has to lift the feed first.


On the other hand, farmers will easily provide feed if the height of the feeder is in accordance with the reach of the breeder.


A good quality cage will also be a comfortable place for goats to live, grow, and breed. Goats can be protected from direct wind and protected from the heat of the sun and rain.


 Goats can also get healthy and refreshing air and can live in peace because they are protected from germs, fleas, flies, and mosquitoes.


With a good cage, goats get maximum care so that they can produce optimally as well. A good cage will also facilitate the use of urine and goat manure to be used as compost so that it can increase the economic value of goat farming.


In a good stable situation, the stable staff will feel comfortable keeping the goats and will be eager to work. Therefore, a good cage size can be judged automatically when we are in the middle of the cage.


Poor housing will be the cause of the failure of the goat business. There are often cases of cempe being trampled to death, trapped between the floor of the cage, or freezing to death. This is because farmers do not provide separate cages for each period of goat life and pay less attention to local wind conditions.


Poor management of the cage will also make the distribution of feed uneven so that the uniformity of goat growth will also be low.


Some fatal events that are actually unlikely to happen are goats dying from maggots in rotting wounds and cases of dead goats hanging in the cage. These two things don't really need to happen if the cage construction is good.


The size of the cage must also be in accordance with the physiological phase, type of goat, and the purpose of rearing. The size of the cage for fattening is different from the size of the cage for breeding.

Monday, September 6, 2021

How to Grow Watermelon in a Pot

Watermelon is a water-rich fruit that must be familiar. The fruit is refreshing and contains many vitamins that are often used as a dessert after eating.




Watermelon is more often grown in dry areas and in rice fields. However, it turns out that planting watermelons can also be done in pots and in a narrow yard. Planting watermelons in pots is actually very easy and you can practice at home.


Watermelon plants can usually be harvested within three months of planting. Of course it would be great if you could figure out how to grow your own watermelon in your yard and pick the fruit in a relatively short time.


Tips on how to grow watermelon in pots guaranteed to grow thick

One way to grow watermelons that are starting to be used often is to use potting media. How to grow watermelon with pot media is very easy to do.


Planting watermelons in this medium will make it easier for you to carry out maintenance, supervision, and control.


Another advantage of potting media is that it does not take up much space. It is perfect for you to put in the backyard, front porch, even in an unused warehouse.


Here are some supports in growing watermelons in pots that you must understand first.


Terms of Growing Watermelon in a Pot


Although how to grow watermelons in pots is fairly easy, you must first understand a few things that support the process of growing watermelon plants in pots.


watermelon growing conditions

Some things you need to know are as follows:


The soil that watermelon plants need to grow must have sufficient nutrients for plants to grow optimally.

The climate around which requires watermelon is in the lowlands or highlands with an altitude of less than 1000 meters above sea level.


Soil pH conditions are suitable for growing watermelon plants in pots. One of them is a suitable neutral pH around 5 to 7 to support maximum results.


After knowing the growing conditions needed, then you can prepare watermelon seeds in the next step.


Watermelon Seed Selection


Good fruit results of course come from good seeds too. Selection of quality seeds is very important to produce quality and fruitful plants.


Therefore, in choosing the right watermelon seeds or seedlings, there are several things you can pay attention to, one of which is as follows:


You can buy good watermelon seeds or seedlings at farm stores with various types and varieties.


The selected seeds must be healthy, shiny black or brownish


The seeds showed good appearance, were not affected by pests and were not abnormal.


After choosing the right and appropriate watermelon seeds, to get good watermelon growth results. The need to get watermelon seeds that grow evenly and healthy is one of them by going through the next stages.


Watermelon Seed Treatment Process

After selecting watermelon seeds according to the variety needed. Then the next step is that you can do the seeding process in the following way:


Clean the watermelon seeds that have been prepared previously.

Then soak the seeds using GDM Fruit Specialist Liquid Organic Fertilizer mixed with warm water for approximately 24 hours. With the required dose in soaking, namely 1 cup of GDM Fruit Specialist Liquid Organic Fertilizer for a dose of 5 liters of warm water.


The purpose of soaking is so that watermelons that have been planted are not susceptible to pests and diseases, especially those caused by fungi and can accelerate the release of potential roots.


The time needed in the soaking process is a day before planting. This is to optimize the growth of seeds to be planted. Supported by one of the premium bacteria in GDM Fruit Specialist Liquid Organic Fertilizer, namely Bacillus pumillus.


Stages of Watermelon Seeds in Polybag

The next step is to plant watermelon seeds while sowing the previously soaked seeds.

6 Ways to Take Care of Banana Trees to Have Big Fruits

Who doesn't know bananas? We are sure if all readers no one answered no. Must also memorize the types of bananas such as Ambon bananas, milk bananas, plantains, kepok bananas, mas bananas, and many other types of bananas.




Banana is a fruit that is found in almost all corners of Indonesia. Trees also grow everywhere, on the roadside, on the river bank, in the yard, in the garden, to forest bushes.


The taste of the fruit is delicious and sweet, and the price is affordable, making bananas loved by all levels of society. Moreover, banana tree cultivation is not complicated, so it makes people interested in planting it.


Terms of Planting Banana Trees


Although easy to cultivate, there are several things that must be considered so that banana trees can grow well. A few of them:


Planted in areas with a tropical climate both in the highlands and in the lowlands with a maximum altitude not exceeding 1600 meters above sea level. But there are also those who say, banana trees can still grow at an altitude of 2000 meters above sea level.


For planting media, bananas can still grow even in less fertile soil. However, good soil is soil that contains loam and a little gravel and is well cultivated. Avoid in waterlogged soil.


For the tree nursery itself, there are two ways to get quality seeds, namely by taking seeds from banana plant saplings and seedlings in the form of shoots on the hump or better known as 'bits'.


How to take care of a banana tree to bear big fruit


Then, to get a banana tree that bears large fruit, care must be taken starting from land preparation, planting, banana trees, maintenance, to harvest time. Previously we have discussed How to Grow Banana Trees. For that we provide tips and tricks on how to care for banana trees so that they bear big fruit.


The steps that must be taken so that the banana tree bears large fruit include:


Land preparation


The soil should be free of weeds or grass. This is done so that nothing inhibits the growth of banana seedlings that will be planted later. Then make a hole with a size of 60 cm x 60 cm, with a height of half a meter with a distance between holes of about 3 to 4 meters.


The distance is given so that later bananas can grow well. Don't forget before inserting the seeds into the hole, you must give 2-3 cans of manure first about 1-2 weeks before planting.


Seed preparation and planting process


For beginners, it is recommended to get seeds by taking banana seeds that grow around ripe bananas. Because this is the easiest way to get banana tree seeds. Unless you know how to get seeds by taking saplings from banana feed, go ahead!


The planting process itself should be done at the beginning of the rainy season, although planting banana seedlings in the dry season is okay. As long as you don't forget to water it, especially at the beginning of planting.


Fertilization


If you want your banana tree to bear fruit, fertilization is the thing to do. One month after the pods are planted, fertilize the trees with a mixed dose of 250 grams of Za, 100 grams of DS, and 150 grams of ZK per plant. Give fertilizer regularly with a span of 3 months. The important thing to note is that fertilization is done by soaking it in a circle around the tree.

Friday, August 20, 2021

The Right Time To Launch Your App

Waktu yang Tepat Untuk Meluncurkan Aplikasi Anda


There is really no doubt for the incredible progress that the mobile app has brought since its inception. To make you understand the importance of mobile devices, see the question above. I think it's pretty clear how we as users are so obsessed with this technology.


The Right Time To Launch Your App


And if I talk about companies, be they big or small companies, they have all understood the dynamics of technological change and have shaped the way they promote their business, which is certainly a smart decision. to make.


But the question that is often asked and I think should be answered is when is the right time for businesses to launch their mobile apps? Should there be factors to consider when introducing your app to the world?


The answer is yes, definitely yes. Changes in dynamics and trends are not only observed by large scale companies, and believe me, they are not the only ones who have been working on mobile technology. Small-scale companies too, knowing how big the profit and high reach of mobile apps are, are also starting to promote their business through mobile apps.


There is no doubt how strongly the demand for mobile apps has grown and every company with the aim of outperforming its competitors is looking for ways to do the best they can, and launching apps is the best they can do.


Obviously, building an app takes a lot of time and effort, but even a high-quality app developed can go to waste if it's not launched at the right time.


So, to help you choose the right time to launch your app, below is a list of factors to get the desired results from the mobile market.


The Importance of Understanding the User Purchasing Cycle Process: Do you know what the most important factors are to pay attention to? This ensures that your app gets to the screens of your targeted users. Understanding a user's buying cycle is one of the most important tools to pay attention to.


When it comes to users, you should know that each individual has their own app download cycle. Some download new apps regularly, while others prefer to download apps once a month. There will also be people who download apps only when they have bought a new phone. Therefore, as a business person, you need to do excessive research on your audience's buying practices and launch your app accordingly.


Know Your Purpose: It is very important to know the purpose of your application. Are you planning to launch the app for an event or will it be used for seasonal sales purposes or are you launching it for everyday use? Knowing your app's purpose creates a powerful impact on your app's revenue.


Choose the Right Time: Businesses with the aim of reaching the consumer market must have a number of strategies. Having an interesting app is one of them. Therefore, determining the exact time, day, week and month of the year plays a very important role when launching your app, as these decisions help your app's success.

Thursday, August 19, 2021

5 Important Factors That Make Apps Successful

5 Faktor Penting membuat Aplikasi yang Sukses


Innovative ideas turn into success stories only and only if executed in the right way. Being a mobile startup, it is important to know that not all mobile app ideas are successful and reach customers.


5 Important Factors That Make Apps Successful


There are dozens of factors that influence the success of a mobile app. Thus, it is very important to point out the essential elements of a successful launch plan.


Define Terms Well


Being a mobile startup, you should know that its success usually depends on the pre-comparison stage as opposed to the coding process. Startups fail mostly because they don't really need the product's user needs. So take some time to list all the smallest details related to requirements, users before starting the coding process.


Keep simple


Contemporary developers take and incorporate as many features into the application as possible. Looking back, you can point out that among the millions of applications available, very few of them provide one because it offers a specific and sharp solution. Therefore, it is important to focus on one aspect and do it perfectly by combining many features on average. Take the smart route to sunrise; start less, check your progress constantly and scale properly.


Look for an Efficient API


A bad API is one of the most important problems faced by mobile startups. It is important to check if the application offers a well-designed backend service. This will result in fast and economical mobile data, thus offering a satisfying experience for the users. Thus, developers and entrepreneurs should focus on the front end and back end of mobile apps to offer better user experience.


the importance of Feedback


Before launching mobile first, it's important to consider beta testers. This is very helpful in removing all bugs and fixing loopholes before launching. You can build a prototype of your idea and reach an audience with it to gather relevant user feedback. Analyzing customer reviews will help you improve them and make them more useful, more interesting.


Make Realistic Goals


Start using mobile devices to cope with the enormous amount of stress associated with scheduling, goal development, and planning budgets. However, aside from this goal, it's important to set realistic requirements and have the features that users demand in your app. In addition, it is important to think and act realistically about the development process and ensure that it is also budget-focused.


Application-oriented startups need to put in a lot of effort to succeed. Your unique idea must go through rigorous testing to understand its market acceptance. Also, it is very important to sign up for an expert mobile app development service from your company who has deep technical knowledge and creative mindset.

Friday, August 13, 2021

How to Prepare for a Successful Sales Interview



They say first impression is everything. When applying for a job, it is very important to have a resume that stands out.


Not to pressure you, but if you made it to the interview, you now need to make a big impression on your behavioral interview. Don't worry because it's easier than it sounds.


Below you will find a guide on how to prepare for a behavioral interview. Keep reading, and we'll help you get the job done.


What is a Behavioral Interview?


Chances are, you've been part of a behavioral interview and didn't even realize it.


In a sales behavior interview, the employer will ask you questions to assess whether or not you have quick problem-solving skills and effective communication tactics. They want to quickly select the best employees who will generate sales.


Know Your Items


Common interview questions for experienced sales positions will focus on your past experience in sales. It's important to highlight your strengths, and it never hurts to do an educational refresher on what you've been taught.


The interviewer will most likely ask about your experience with different sales strategies, the different software you use, and administrative processes. They are looking for pre-qualified candidates to select the final people.


When answering their questions, be sure to answer tactfully. They will be able to tell if you are saying empty words just to fill the silence. It's okay to gather your thoughts for a moment before answering.


If you're a little unfamiliar with software programs and control systems, find video tutorials or take online courses. Even learning some well-known sales vocabulary will help you in the interview.


Practice Your Answers


Practicing your answers to common sales behavior interview questions will prepare you.


Be prepared to answer questions about your organizational skills and what a typical day in sales looks like to you. You'll also want to know how much time you usually spend working with clients.


Make a mental note of how you prioritized your tasks and clients during a busy week and what you did if one of your clients was particularly difficult. You may even be asked how you have handled a difficult supervisor in the past.


Remember how you talked about difficult individuals saying much about your character.


Other questions you receive may focus on what you do when a client drops you, the presentation you give to the client, and the goals you have set for yourself in the past.

Thursday, August 12, 2021

Model for Predicting Job Interview Results



The ability to predict interview outcomes can help voters decide whether to attend a job interview or more importantly, perhaps not ask which job interview questions they need to improve in order to increase the job offer for the position. where they have the associated skills, competencies and confidence.


The interviewer makes interview choices based on the interview - the job analysis process is designed to predict future performance.


Decision making, however, is a two-system process. partially logistic - slower analytical process and emotional - quick judgment based on stereotypes and judgments.


Therefore, an employee applying for the same position, in the same organization, providing the same detailed explanation for the same interview question may receive different scores if interviewed by two different managers.



There is a two-step process for forming an opinion in a job interview


  • Subconscious bias
  • Interview Identity
  • Job interview bias.


The initial impression is made after the interviewee is introduced to the employer. Emotional impressions - hunches, where stereotypes and subconscious about the formation of the interviewer's perception.


Many varied stimuli trigger unconscious biases, some advocates being supportive, while others creating negative opinions. Research has shown how weight, ethnicity, age, religion, attractiveness or background can be used subconsciously to shape interviewees' opinions.


Having something in common can increase the liking between the employer and the search, increase the likelihood of developing job inquiries (affinity base) and mutual liking, being liked by someone because they like you, and building rapport.


Seen as a 'raising manager' view of challenges, even to the point of increasing the level of trust they hold in applicants.


And hearing how one promotion candidate is a strong candidate, for an internal interview, can give you an idea of ​​the offer by creating a 'halo effect'.


Association is a strong bias. Research on religious bias found how attractively changing his name to 'Mo' increased the number of interview offers he received. And age, race, and gender match well to add or subtract each applicant for their advertised old position.


An example is how women apply for traditional male roles that are incompatible with men.


The power of the subconscious in a job interview.


This opinion is the conscious mind. Entrepreneurs, in most cases, are not aware of the subconscious biases that come into play.


The interviewer, in the example of a woman applying for a job in a male role, is not sexy. In contrast, subconscious bias affects, to a lesser extent, how judged during a job interview. With so many promises made with little difference between a successful and a second choice, therefore, combining these points can make all the difference.


Entrepreneur's reaction to stereotypes.


some people have 'problems'; sexist, ageist, racist, and many other issues. We classify these individuals as Conscious and Unconcerned - if the applicant has a stimulus that the employer does not like, it will be difficult to change the initial opinion even when evidence to the contrary has been presented.


Conscious and Caring - when subconscious biases become apparent (interviewers realize they like and dislike for no reason). Consciously, interviewers can challenge themselves.


If for example, a recruiter makes a negative opinion about a candidate based on obsession (a study was completed in which applications were sent with a candidate's image. Half were sent with obsessive imagery and the other half were sent with obsessive imagery.


image of an 'average' weight candidate. The experimenter found that being overweight was less likely to get a job interview offer), they could ask whether weight was important for the job in question? Or find examples of overweight employees who are very successful in their fields.

Difference Between Certified and Notary Translation



Prospective clients often ask what is the main difference between certified translation and certified translation. How is it different? Simply put, only a professional certified translator can provide you with a certified or verified translation of a document.


Certification involves preparing an officially signed translator's statement and rubber stamping or embossing each page of the document with a professional seal from a professional. In other words, certified translations come with quality assurance because the skills and experience of translators are certified by several official regulatory bodies. Being a professional certified translator, one can attest to the quality of the translation.


In contrast to this, a Notary Certified Translation can be provided by anyone. There are no mandatory or mandatory quality requirements as translators do not need to be certified. The only official aspect of this process is that the translator will swear and sign the affidavit in front of a notary. Notaries will only ensure that He has given wording that the translation made by them is a true representation of the original document but does not judge the quality of their own work.


Who needs a certified translation or notary?


In short, translations for contractual, legal or immigration purposes, for example, service agreements, birth certificates, court transcripts, or marriage certificates often need to be certified. While the translation of administrative purposes, such as university or college admissions, may only need to be notarized. In some cases, clients may also request certified and authenticated translations. The notarized document adds an additional layer of validity to the certified translation form, which can stand alone or can be accompanied by a notarized written statement, depending on the client's requirements.


Which service is more expensive?


For translation actions, translators typically charge per word, page, or hour, regardless of whether they want a certified or standard translation service. 


Who needs a notarized translation?


They are required by most of the universities, colleges as well as evaluation institutes when one submits their educational documents for evaluation. Notary translations are also required by law firms, proceedings, mortgage companies, and employers. One can also verify with the authorities where they plan to use the translation whether a certified translation is sufficient or some kind of notary certification is required.


Some companies offer translation services both certified and certified translations, also within 1 to 2 days at a flat rate. If you are unsure about the difference between certified translation and certified translation or need help, it is better to seek professional help. Experienced managers will answer any questions regarding the translation services we offer.

Tuesday, August 10, 2021

Causes of Diesel Cars Difficult to Live



You need to understand that diesel car engines certainly have different characteristics and work systems from gasoline-fueled cars.


Of course, the way of maintenance and various problems are also different between the two car engines. For this reason, a deep understanding is needed, especially regarding diesel car engines.


Because, very few people know how to care for a diesel car engine. Given, in the application itself does have different treatment steps.


One of the problems that often becomes a scourge is that diesel car engines are difficult to start or turn back on.


Causes of Diesel Cars Difficult to Live


Of course if this could be a problem it would be difficult to start the engine when it's cold or early in the morning.


Constraints like this are often found in diesel engines that have been used for a long time, even new diesel engines can experience this if the engine lacks maintenance.


But as a diesel car owner, of course you have to understand what makes a diesel car difficult to live. Let's see the review together.


There are several factors that cause diesel engines to be turned on both in the morning and when the engine is cold even under normal conditions. Among others, as will be explained in the discussion below.


Causes of Diesel Engines Difficult to Start in the Morning


Low battery

It should be noted that the starter system on a diesel car of course uses a battery or power as a power source to drive the power to drive the motor dynamo.


If in this case the battery has problems, such as weak voltage, it will affect the process of starting the car engine.


Usually the low voltage here will be marked with a stuttering engine as an indication that the starter dynamo cannot start the engine due to a lack of power supply from the battery.


To solve problems like this, of course, one way to overcome them is to check the condition of the battery in the car.


If the battery is good but the voltage is reduced, of course you only need to charge the battery until the voltage returns to 12 volts.


Meanwhile, if the battery in a diesel car that functions as a battery here is bloated, that's a sign that its capacity has begun to decrease.


That way, it would be better if you replace the battery if it is really damaged or the main cause of diesel cars starting is due to low battery voltage.


Stop contact

In addition, there is one component that is involved in access or influence when a diesel car engine is started. Namely glow plugs or glow plugs.


The glow plug component here functions to heat the combustion chamber within the scope of a diesel car engine.


Generally the combustion chamber will be turned on in the morning or when the engine temperature drops dramatically, so it needs to be supported by a glow plug to raise the temperature so that the combustion process can still be carried out even in low temperature conditions.


These glow plugs are located in each cylinder. If one of the glow plugs is damaged, the effect will disrupt the system or the combustion process in one cylinder


If only one died, the effect would not be too pronounced. However, if both glow plugs die, the diesel will be difficult to start, even for the engine to start.


Obviously this condition is because the temperature in the combustion chamber does not exceed the point of diesel fuel. So, the car engine feels very difficult or stutters when turned on.


Air To Fuel Line

In addition, the cause of diesel cars turning on when turned on, does not rule out the possibility of being triggered by flu symptoms.


The wind in the diesel car in question refers more to the condition of the air entering the diesel engine fuel line area.


Generally, the air intake is triggered during the process of replacing the air filter on a diesel car engine.


The problem lies in how the air can be compressed so that when the fuel pump starts operating it will trigger a pressure that only fuel and air get pressure.


In conditions like this, of course, it can cause the diesel fuel coming out of the injector to be disturbed by the presence of air in the injector system which will cause the engine to be disturbed when it is turned on.


Therefore, to work around this, you can manually apply pressure to the solar tip to expel the air in the fuel injector from the fuel line.


However, it is recommended to do it in a workshop because it requires experts so as not to trigger damage to other components.

This Causes Car Engine Oil To Drop Fast




There are various factors that trigger the oil in a car engine to run out quickly that many people rarely realize.


Car Engine Oil Runs Out Fast – Engine oil in a vehicle is certainly one of the most important aspects to always be maintained. Including four-wheeled vehicles.


Of course, the presence of car engine oil will greatly affect the condition of the car engine system. Where, as a fluid that functions as a lubricant while maintaining the temperature inside the engine.


Therefore, every car owner must always check the oil regularly considering its indispensable role in running the engine operating system.


Because, if not treated, there will be many problems. Like a car engine oil that runs out quickly which is often not realized by the owner.


Causes of Car Engine Oil Running Out Fast


If this is allowed, it will trigger various consequences of running out of car engine oil. Which, it will not be far from the runway system on a car that is easily damaged and worn out.


For that, you must understand what causes car engine oil to seep which makes it run out quickly even though it has just been replaced.


Thus, the problem of running out of car oil can be minimized with maximum prevention efforts.


Well, below are various reasons that cause car engine oil to run out that you need to pay attention to the characteristics and triggering factors.


In some cases, the engine oil in the car will decrease gradually. However, if suddenly the volume of oil decreases drastically, of course there are factors that cause it. Is as follows.


Signs of Car Oil Starting to Reduce


There is Seepage in the Oil Line

First, it is very possible if the problem is that the oil runs out easily because the drain plug that functions to drain the car engine oil is leaking.


As the engine ages, these components are often disassembled while the engine is still hot, potentially damaging the drain plug.


Usually a leak that occurs because the rubber seal that prevents seepage out is brittle or worn. So, you should replace the rubber seal first.


However, if this problem cannot be solved, you should immediately replace the drain plug component if the condition is very severe.


Or, if it's urgent, you can work around this by coating the sealtip on the threaded part of the engine block with a drain plug as a temporary measure to keep the oil from escaping.


From this it is very logical if the oil in the car runs out quickly because it seeps out because the rubber seal or the dran plug has been damaged.


Seepage in Carter/Oil Pan

In addition, other causes besides the condition of the car engine oil leak can also occur in the oil pan component.


The oil pan or charter here functions as a reservoir for engine oil which will later be distributed to the entire engine block area for lubrication.


Usually this part of the connection is often the main cause.

Recognize Car Water Pump Problems and Their Characteristics



Every component in the car certainly requires attention in the form of maintenance measures to keep it durable and long lasting.


However, every maintenance step requires the right steps so that later the car component maintenance process can be carried out correctly and perfectly.


Well, one important aspect that is often rarely noticed by car owners is the car's water pump.


It should be understood that a problematic car water pump is generally triggered due to several factors which are actually quite trivial.


Broken Car Water Pump Sign


It's just that, it is often ignored, causing damage or problems with the car's water pump.


Where in general the problem with the water pump on the car lies in the bearing area which has begun to not be able to run its working system.


Usually the condition of this bearing damage will be indicated by the appearance of a rough sound when the car engine is turned on.


Well, for that as a precaution, of course you need to recognize the various factors that characterize a problematic car water pump. Come on, check the complete info.


There are several factors that certainly characterize the condition of the car's water pump damage. Here are the signs you need to understand.


Sound Appears from Machine Area


Generally, damage to the water pump on a car will usually be marked by an indication of the appearance of a sound coming from the hood area of ​​the car.


This sudden sound usually appears because there is damage to the water pump bearing.


To be sure, of course you have to check it by removing the fan belt and then turning the water pump by hand.


If the damage to the water pump is too severe then when the water pump is rotated it will usually feel like it is stuck on one side.


However, if you feel the pulley on the water pump sway sideways when you hold it, then it is an indication that the water pump is making a louder sound.


Water in Radiator Not Circulating

In addition, if the condition of the water pump on the car is problematic, it can be seen from the condition of the radiator water.


Usually the water in the radiator will not circulate properly. The reason is, the car's water pump which is supposed to function to pump radiator water has a problem, causing the radiator water to not work.


Meanwhile, to check it, you can see the radiator cap hole when the engine is idle. If the condition of the water pump is in normal condition, the radiator water will appear circulating.


If the condition of the water pump fluid still does not move, then that is a sign that the water pump is not working.


Well, from here it can be a sign for you that the water pump cannot run which requires you to check its condition or replace it with a new one.


Radiator Fan Rotates Non-stop

In addition, it cannot be denied that the relationship between the radiator component circuit and the water pump is very close.


So, you can also recognize the characteristics or signs of a problematic water pump from the condition of the radiator fan that continues to rotate without stopping but the temperature in the engine does not change or remains hot.


This condition is of course due to the absence of a radiator water cooler that is able to stabilize the temperature caused by the radiator water not circulating because the water pump as the driver cannot work properly.

Causes of dead engines on motorcycles



One of the fears when driving on the highway is when the motorcycle being driven suddenly turns off the engine. Especially if the path taken is a small road far from the workshop and no one can help.


You may have experienced something like this. If not, you should pay more attention and pay attention to the condition of your motorcycle. Motor that died suddenly, generally caused by the condition of the motor that is not prime.


Fuel

Motor vehicles need fuel to work. If the engine suddenly dies even though the engine has been properly cared for and routinely performs maintenance at an authorized workshop, fuel could be the main cause.


The type of fuel used has a major effect on the combustion process of each motor. Low octane will cause a lot of loose lead that clogs the valve so that the motor shuts down suddenly. Using fuel with a higher octane, can maintain the quality of the motor engine and prevent engine failure.


One of the causes of sudden death of a motorcycle engine is also caused by a blockage of the fuel line entering the carburetor. This blockage can be caused by dirt in the gas hose to the carburetor so that gasoline is not normal or even cannot flow.


Includes air filter.

The function of the air filter is to filter the air that enters the combustion chamber so that it does not mix with dirt and dust so that the air and gasoline mixture is more perfect. If the condition of the air filter is dirty, it will cause a heavy gas pull and the motor will stop suddenly or break down.


Engine Overheated

The cause of overheating in the motor engine is due to the blockage of oil circulation in the engine. The piston rings become dry so the motor suddenly shuts down. Hot temperatures arise from the combustion system or from the friction that occurs between the piston and the boring liner. The heat that cannot be removed by the lubricant makes the temperature rise rapidly, as a result the piston expands and is trapped in the boring liner.


Engine oil on a motorcycle can be reduced because it is used for long distance trips which can cause the oil to evaporate through the pores of engine deposits. Engine oil is reduced due to a weak piston ring which causes the motor to emit smoke due to burning oil. That way the oil will decrease continuously so that when riding a motorcycle in hot temperatures causes the motor to die suddenly.


Ignition

The motor ignition system also consists of a spool, kiprok, CDI, and ignition coil. Spool and kiprok are the main components to supply electric current to the motor electrical system. If there is a problem with the electric current, the spark from the spark plug will not ignite and combustion will not occur. If combustion does not occur then the motor will not be able to start.


Perform Routine Service

Under certain conditions, a spark plug that is too small can cause the engine to stop. A damaged motor engine is an early symptom of damage. When the sound of your engine starts brebet, combustion does not occur completely. As a result, the power becomes low for compression and the piston stroke will stop. This is what causes the engine to die suddenly.


Make sure you always service your motorcycle engine at an authorized workshop on a regular basis. Perform routine service every 2 months so that the condition of the motor remains according to factory standards.

How to Overcome a Sudden Dead Injection Matic Motor



People like this means of transportation because it is considered more efficient than having to drive public transportation. In addition, the price is also relatively more affordable than having to buy a car.


Especially now that simpler motorcycle technology is being created. Yes, now we are starting to make automatic motorcycles where all you have to do is step on the gas. Even so we also need to be careful when driving it.


Generally for motorcycles now do use the injection system. This injection technology is considered better and more sophisticated in use. However, what if it turns out that your automatic injection motor dies suddenly while driving? Wow, that sure sucks.


To solve your problem, of course you need to understand the cause first. Knowing the cause of the automatic injection motor turning off suddenly can make your problem immediately resolved. Especially if you are traveling and far from the workshop. So the mastery of science to overcome the problem of this injection motor is very necessary.


Causes of Automatic Injection Motors Can Turn Off Suddenly


Actually the cause of the automatic injection motor can die suddenly can be due to various things. The solution to each problem will of course also be different. Well, in this article we will directly discuss it. Come see!


1. Fuel Out

The cause of the first automatic injection engine to die is running out of fuel. So for that, when your motorbike suddenly dies, don't panic first. Please note that injection technology requires you to keep the motor from running out of fuel. The EFI technology used creates fuel pressure in the fuel line system. If the fuel in the motor runs out then there will be air entering the fuel hose. This also makes the motor difficult to start.


Even so, you don't need to worry because EFI technology can blow air out of the hose. The solution to this problem is that you can refuel your vehicle's tank first. If you keep turning the contact in the ON direction by holding it down for four seconds. After that you can return the contacts to the OFF position. Repeat this method up to five times.


2. Battery Error or Damage

The second cause of the automatic injection motor shuts down suddenly is a faulty battery. If on an ordinary motorcycle the battery is only used for the starter process, then the injection system is different. In motors that have an injection system, the battery serves to maintain the stability of the motor's electric current. If the battery is short, the voltage will drop and the motor will shut down. Now for the solution you can replace this battery.


3. Fuel Pump Off

In this case the gas pump or fuel pump is indeed owned by a vehicle that has EFI technology. The function of this fuel pump is to supply motor fuel to the tank and fuel lines. Please note that if the fuel pump cannot operate properly, it will create fuel pressure in the motor. So that gasoline will not come out of the injector. You can tell if the fuel pump is working when you hear a buzzing sound from the tank when the ignition is in the ON position. The solution you have to replace the fuel pump.


4. Spark Plug Problem

Spark plugs can be one of the problems that causes the automatic injection motor to die suddenly. As we understand if the spark plug plays an important role in engine combustion. Symptoms of motor disorders in the brain can also be seen when the motor suddenly turns off and is difficult to turn on. To overcome a damaged motor bus, of course, you have to replace it with a new spark plug.


5. Sensor is broken

Motors that use EFI technology are also used to using sensors. This sensor can function to check the state of a certain area. Please note if any data has airflow and intake airflow temperature sent by the sensor. Damage to the sensor can cause the engine to start imperfectly and eventually die. The sensor is faulty or you don't know when you took it to an authorized repair shop. Remember not to tinker if you don't understand.

Causes of Motorcycles Often Jammed and How to Overcome



On a motorcycle there are many moving components and parts that must work hard when the engine is running. Due to continuous use, the performance of some components may decrease.


A damaged motor is actually an indication that some of your favorite motorcycle components are experiencing problems and a sign that you need to do service.


This brebet symptom usually appears when the motor is running and the gas grip starts to spin deeper. The motor pulls intermittently and in some cases the motor even dies and breaks. Just imagine, for example having a motorcycle accident while overtaking or being in the middle of the highway, of course it can be very dangerous.


Some Carmudians must still be confused about why their favorite motorbike could crash. Actually, some of the causes are not due to serious problems but need immediate treatment. If left unchecked, the motor feels uncomfortable and the damage can spread to other parts.


A motor that breaks down suddenly is quite dangerous


In general, the cause of the motor brebet because the comparison in the combustion chamber is not up to standard. This is because the type of fuel that is not suitable and automatically makes the engine combustion less than perfect.


There are several other causes of brebet motors that must be known so that later they can make repairs quickly. This method of handling can also be used as a prevention so that the motor does not tense up again when gassed at high or low rpm. Curious what causes it? Come on, let's go a step further.


Improper use of fuel is a common cause of motorized vehicles. Many motorcycle owners deliberately use fuel that is not in accordance with the standards set by the manufacturer on the grounds of being more efficient. On average, motorists prefer cheap fuels, such as Pertalite or Premium.


Collisions like this occur because of knocking on the engine which causes the motor to break down. For that, check the owner's manual or find out the compression of your motorcycle engine and what fuel is right. By using the appropriate fuel and of course by the manufacturer, the symptoms of brebet can disappear.


Spark Plug Start Soak


Motor spark plugs that must be replaced with new ones so that motor performance remains optimal


The next cause that can make the motor crash is due to a weak spark plug. The stun flow cannot be completely changed, causing a fire in the combustion chamber. Fires which of course make the combustion not optimal so that symptoms appear brebet.


If the spark plug is not in prime condition, such as dirty, too loose or even damaged, combustion in the engine compartment will be less than perfect. To fix this, make sure the condition of the spark plug is still good. Spark plugs that are not good or dirty, make combustion so choked and incomplete.


If you see a lot of black soot, look at the spark plugs first and then put them back in. But if the problem still persists, you will have to replace the business with a new one. Before reinstalling, do not forget to check the spark plug gap is too loose or normal.


As a rule, if the gap between the spark plugs is more than 1 mm, we recommend replacing it with a new one. When replacing spark plugs, choose a cooler type, for example NGK7 the number is 8 or 9, this is because cold spark plugs are more resistant.


Dirty Air Filter


The cause of the brebet motor on this one is actually easy to overcome. Over time, the air filter gets dirty over time as it filters dust from the air that enters the fuel chamber. Well, this accumulated dust, if left unchecked, makes the air filter gap clogged. As a result, the injector or carburetor cannot suck up air optimally.


You need to know, the service life of the owner's manual air filter reaches a mileage of 16 thousand kilometers. This use is faster if in urban areas or industrial areas that have a lot of dust. A clogged air filter can cause the motor to stop and the engine to stop suddenly.

How to increase ranking in google search



Every site owner, be it a website or blog, always wants the website he owns and manages to enter and dominate the top position in search engine results, such as yahoo!, bing, ask, etc., especially the google search engine.


Many things are behind this, including search engines which are considered as a means to bring in visitors with the right target.


A person who, for example, types the word "selling futsal shoes" through a search engine, he is most likely a person who wants to buy futsal shoes online, and when our website sells futsal shoes and appears in a search engine, that person will most likely visit the site. the. NS.


SEO exists because of the results of research by experts or those who are experienced in getting the best position in search engine searches. In forums both online and offline, there are a lot of discussions about SEO, but again this is only based on their research, not about leaked Google algorithms. From most discussions about SEO, they always find the following things to get a good position in Search engines.


The secret of how to increase the position of a blog in google search

 

This site loads fast loading


This is part of what is called On page SEO, or SEO optimization that we do to improve our site. By having a site with fast loading and light weight, it makes it easier for robots from search engines to crawl all site content and then display it in search results.


Maybe many of you prefer web designs that are complicated and look beautiful with various ornaments, but this turns out to be burdensome for loading a site. JavaScript type script is one of the things that is touted as one of the things that makes a site heavy.


But of course we really need javascript to design a website, so use javascript well. Another cause is content in the form of flash or video which is the biggest contributor to the slow running of the web.


Nice site structure


A good web structure is one that has a valid programming language, whether it's a script in the form of css, html, php, etc. Make sure our site has no errors in script writing, now there are many tools to identify whether our web site has many errors or not. We can find out through online sites such as w3 or by using software.


The use of the Heading tag on a site is also very important, so that search engines can find out the titles and subtitles on each page on a site. The h1 tag for the title is one of the most important factors in SEO, many seo experts recommend using this tag. Also use the meta description so that search engines can find out the short contents of the page that we create


Submit sitemap


A sitemap is a sitemap in XML form. By creating a sitemap, we intend to provide all of the table of contents on our site, as well as tell search engines which pages may and may not appear in their searches. So when we create a sitemap, make sure not to include pages that should not be indexed (not displayed on search engines) in the sitemap, in addition to blocking which pages should not be indexed we can use a file in the form of robots.txt. txt.


With a sitemap, all the pages on our site can appear both on Google and other search engines. With the number of indexed pages means the greater the chance of a site getting a lot of visitors.


When we have created a sitemap, we can submit it to Google Webmaster for Google search engines and Bing Webmasters for Bing and Yahoo search engines.


Get backlinks


Backlinks or backlinks are links from other sites that point to our site. In SEO, backlinks are one of the Off page SEO methods or seo methods that are carried out outside the pages of our site. Google and other search engines believe when a site provides links to other sites that the site has endorsed the site.


For example like this, when site A provides a link to site B, the search engine believes that site A already supports site B. Therefore site B will get a higher place in search results than site A. The more sites get backlinks, the bigger it most likely comes from a site that shows up in the top search results of google.

Signs that the V-Belt Motor Matic is starting to break and must be replaced



As we know that the v-belt component on the automatic motor is one of the important components.


Not without reason, considering that the v-belt has a role as a wheel drive on the scooter which will certainly cause problems if the v-belt component experiences problems.


One of them is the problem of age. Which, if it's like this, of course, must replace it with a new v-belt.


The problem is, when is the right time to replace the v-belt on an automatic motorcycle?


Well, regarding this, of course, before deciding to buy a new van belt, Ana must first know what the symptoms are if the scooter's v-belt needs to be replaced.


Where, there are several signs that can be a 'message' from the motor that it is time to replace the v-belt with a new one.


Alright, about this Mas Sena will give a little info about the characteristics of the automatic motor v-belt that is starting to break and must be replaced with a new one.


  • Always Service Routine to Control the Condition of the V-Belt
  • Avoid Using Heavy/Wrong Wheels
  • Avoid Riding a Motorcycle with Shock Pull
  • Signs of Damaged and Worn V-Belt Motors


In some cases, there are certain characteristics that indicate in case of irreparable damage to the v-belt. Instead, it should be replaced with a new one. Here are the characteristics.


V Belt Mark Must Be Replaced


Rubber V-Belt Starting to Crack

The first thing that can be seen with the eye that characterizes the v-belt that must be replaced is the condition of the v-belt rubber that is starting to crack.


You can easily see the physical signs of a motor matic v-belt that must be replaced, namely by looking at the curve by forming the letter V on the jagged part.


There are cracks in each section of the groove which is an indication that the v-belt is worn and it is time to replace it.


In some cases, this condition is not a problem. But if left too long will worsen the condition of the motor. Especially the parts or components that are directly related to the v-belt itself.


Motor Pull Feels Heavy


On the other hand, if you feel the pull of the automatic motor starting to feel heavy, then it could be a sign that your scooter's v-belt is starting to wear out and become brittle.


Such conditions are certainly the effect or impact of the v-belt which is no longer able to grip the wheel drive area which makes it feel heavy when driving on the highway.


Therefore, if you start to feel that something is wrong with the pull of the automatic motor, try checking the v-belt.


Because, in addition to late service, weak motor pull is also an indication of a weak v-belt which of course needs to be replaced with a new one.


You can check the automatic motor v-belt and its routine service. So, if it's time to replace it, you should immediately replace it with a newer one.

Examples of small capital business big profits



Doing business does require the right time to get a great opportunity to generate profits. But if you have a mature business concept and strategy, maybe now is the right time for you to start a business.



1. Follow your instincts



Business or business is where you make money and profit, so you should enjoy it while running it. So for that, you have to follow a passion that makes you happy to run a business. For example, if you love food, a culinary business might be the best choice. If you love pets, a pet shop business is not a bad choice. In addition, following your passion also makes you more enthusiastic in building a business and not giving up easily in solving problems.



2. Market Analysis



Market analysis is an analytical activity to learn various things about market conditions, so market analysis is a must for those of you who are just starting a business. The benefit of market analysis is that it will be easier for you to get customers, see the competition, take advantage of opportunities, reduce risks, prepare long-term plans, and much more. So don't forget to do this step for the smooth running of your business.



3. Separate Capital and Profit



By separating capital money from profits, you will more easily control your income and expenses. You can create two different accounts to separate them and record each transaction on the books, thus avoiding you from using venture capital for personal gain.



Promising Business Opportunity




1. Healthy Food Business



Recently, people have started to care about their health by maintaining a healthy diet. For that they need healthy food to support their body health. Healthy food catering does exist, but not many, so it is still difficult to find in some places. Now you feed them healthy food, because they are willing to pay more for healthier food. There are so many healthy food recipes that you can find on the internet, then you innovate them so that they become delicious foods that you can sell.


2. Franchise Business




A franchise or franchise is indeed a business that doesn't need to think too much about branding the product you want to sell, because you will buy a franchise license from an existing brand. What you need to think about is what brand you want for your business, because so many franchise providers are big names. You can purchase a franchise license in the food & beverage sector or retail stores.



3. Pet Shop Business



You could say that pet shops are not widely available in some areas, so people have to look for pet shops in more distant locations. This is your chance to open a pet shop in a location where there is no pet shop, because your pet shop will be the target of people to buy their pet needs.



4. Shoe Washing Business



Most annoyed if the shoes are wet and dirty when exposed to rain, so a shoe washing service is needed. You can indeed run this shoe washing business, because this business is quite easy. Prepare the needs for washing shoes and washing techniques. Don't forget to also know the existing shoe materials, to avoid damage to the shoes you wash

Small capital home business ideas



The more considerations you think about, making the dream business/business never come true.


But sometimes, extraordinary results can start from the simple thing of starting a business from your own home.


If you think about it, there are many aspects that you can turn into a very lucrative business opportunity.


#1 Refillable Drinking Water

You can use one corner of the house to run a refill drinking water business. The community's need for this commodity is very large.


In addition to being practical, the need for clean water is also decreasing in some areas so that if you can maximize this business opportunity, it is not impossible to get a large income.


#2 Daily Catering

In the culinary world, you can become a daily catering provider.


The busyness of the community today makes it difficult for them to take the time to just get food to eat so that daily catering is one of the solutions used.


#3 pound of laundry

Perhaps one of the activities that people don't like today is washing clothes.


As a result, laundry services have become one of the most in demand. You can take advantage of the kilogram laundry business opportunity that you can do at home.


#4 Tailor

If you have the passion and skills that support a tailor and clothing designer business, of course you can start from your own home.


Fashion transformations and trends are interesting things to explore. And of course it is also very closely related to the business value which is quite tempting.


Therefore, this business opportunity is very promising and has good prospects in the future.


#5 Snack Packaging Business Opportunities

Snacks are one type of food that is quite loved by many people, such as snacks from cassava, potatoes, and many more.

Causes of Missing Articles From Google Search Engines


Articles are one of the most important parts that determine whether or not the search engine rating (google, bing, yahoo, yandex) on a blog.


Many bloggers are looking for ways to get the posts they publish to appear on the first page of search results.


But have you ever realized, why blog articles don't appear or even disappear from the Google search engine? There are several factors that cause articles to disappear from search engines. As I have explained below.


The cause of the article missing from the google search engine


1. Blog age is still new


If your article or even the blog/site itself doesn't show up in Google searches, it's usually because your blog is still relatively new.


This issue is common and will be resolved over time. You just need to be diligent in writing articles on a regular basis. Don't be shy about trying to introduce your blog through social media. The most important thing is to follow the procedures set by Google on how to introduce a new site. What you can do is the following:


Register your blog to webmaster google, bing and yahoo.


Create a sitemap/sitemap on the webmaster.


Inserting the webmaster meta tag into the blog is intended to verify site ownership.


Submit the url of the article you just published.


Keep your blog healthy by regularly writing articles and visiting other blogs.


Given the age of your blog is still new, at this stage the Google search engine is still indexing your site.


The length of time for self-indexing is uncertain. Because in this case usually the time required by search engines varies greatly. But the more often you publish articles, it will make your blog indexed faster.


2. Google Penalty Blog


Another reason why your blog is not showing up in Google searches is the possibility that your blog has been penalized by Google. Generally this penalty will be given to bloggers who have very bad activities in managing their blogs.


As in making irregular backlinks. Leave irrelevant comments that are considered spam by blog owners. Excessive comments on sites with active links are included.


Including too many keywords in an article can also cause your article to disappear from search engines. Because Google thinks your article is not high quality. So, write articles that are easy and easy for visitors to read.


3. Selection of the wrong keywords.


In this case you have to be more selective in choosing keywords. If you want your articles to be indexed quickly and perched on Google search pages, try to target long-term keywords. Such as the discussion of education, android, computers, recipes, etc. which include basic material. Don't write anything viral, because viral articles won't last long on search engine pages.


4. Competition between blogs


This last point is certainly a very common thing in the world of blogging. The tight competition between blogs that have the same topic/niche will of course also affect the position of your article.


In terms of competition, many factors determine, including blog age, SEO, quality of writing, backlinks, DA PA etc. If you don't have all of these aspects on your blog, don't expect to beat the competition. . in search engines with the same keywords.


If you have trouble even want to quickly prove that your blog article is in the top position. Write articles that don't say much. For example the local wisdom of an area, local tourism in the area. The point is there are still many who do not know.

Reasons Why Your Site May Not Be Indexed




After further discovering the problem, I thought I'd write a post for Moz to share my experience so others don't have to spend a lot of time looking for answers about indexing.


This means that your site, or any part of it, is not added to Google's index, which means no one will find your content in search results.


list of Crawl Problems


The first thing you should look at is your Google Search Console dashboard. Forget all the other tools available. If Google sees a problem with your site, then that's the problem you want to address first. If there is a problem, the dashboard will show an error message. See below for an example. I have no issues with my current site, so I'll have to find someone else's screenshot. Thanks in advance, Nile :)


Crawl


The HTTP 404 status code is most likely the one you'll see most often. That means whatever page the link points to, cannot be found. Anything other than a 200 (and possibly 301) status code usually means something is wrong, and your site may not function as described to your visitors. 


Fix Crawl errors


Usually this type of problem is caused by one or more of the following reasons:


Robots.txt - A text file located in the root folder of your website that conveys certain guidelines for search engine crawlers. For example, if your robots.txt file has this line in it; User-agent: * Disallow: / basically tells every crawler on the web to climb up and not index ANY content on your site.


.htaccess - This is an invisible file that is also in your WWW or public_html folder. You can enable visibility in most modern text editors and FTP clients. Very bad htaccess can do bad things like infinite loop, which will never let your site load.


Meta tags - Make sure non-indexed pages have no meta tags in source code: <META NAME="ROBOTS" CONTENT="NOINDEX, NOFOLLOW">


Sitemap - Your sitemap is uncertain for some reason, and you are still submitting the old/broken one to Webmaster Tools. Always check after you've resolved the issue that's shown to you in the webmaster tools dashboard, that you've run a new sitemap and resubmitted.


URL Parameters - Within Webmaster Tools there is a section where you can set URL parameters that tell Google what dynamic links you don't want to index. 


Your Pagerank is not enough - Matt Cutts revealed in an interview with Eric Enge that the number of pages that Google crawls is roughly proportional to your Pagerank.


Connectivity or DNS issues - Maybe because of whatever Google spiders can't reach your server while they try and enjoy it. Maybe your host is doing some maintenance on their network, or you've recently moved your site to a new home, in which case DNS delegation could satisfy crawler access.


Built-in problem - You may have registered a pre-existing domain. I have a client who gets a new domain (or so they think) and does everything according to the books. Writes good content, nails things on the page, has some great inbound links, but Google refuses to index them, despite accepting their sitemap.


After some investigation, it turned out that the domain had been in use a few years earlier, and was part of a large www linkspam. We had to file a reconsideration with Google.